目錄號由各種字符組成，每個字符標識該組件的一個特定選項。使用下面的目錄編號圖表來了解組件的配置。有關產品可用性的問題，請聯系您的Allen-Bradley經銷商。

清除物品內部和周圍的所有包裝材料。開箱后，根據訂購單核對目錄號，目視檢查電纜和每個連接器是否損壞。如有必要，立即通知承運人任何運輸損壞。
電纜以線圈的形式儲存和運輸。在拉直電纜之前，電纜保持這種形狀。要拉直電纜，可以從其中點懸掛一根短電纜，或?qū)⒁桓L電纜沿直線放在地板上。在接下來的24小時內，電纜中的任何線圈都將被拉直。這種做法使電纜更容易安裝。

單根電纜使用的電纜技術是相同的，無論目錄號如何。每根電纜的不同之處在于引線準備和反饋導體端子。
?2090-CSxM1DF電纜導體具有飛引線和引線制備，專為Kinetix 5500伺服驅動器設計。不需要現場鉛準備。
?2090-CSxM1DE電纜包括2198-KITCON-DSL連接器套件。該套件與反饋導體預組裝，飛引線功率導體的引線準備是專門為Kinetix 5700伺服驅動器設計的。不需要現場鉛準備。
?2090-CSxM1DG電纜導體具有飛引線和引線制備，專為Kinetix 5500或Kinetix 5700伺服驅動器設計。不需要現場引線準備，但是，2090-CSxM1DG電纜引線比2090-CSxM1DF電纜引線長，以適應任一驅動器系列。

這些數字說明了如何測量彎曲半徑和電纜彎曲的地方可以在單電機電纜上。在系統安裝過程中，布放電纜時，請與電纜引腳和規格表配合使用。

為了滿足Kinetix 5700伺服驅動系統上的電機制動電路的當前要求，電纜長度超過50米(164英尺)，2090-CSBM1DE (B系列)電纜可與18 AWG制動導體一起使用。B系列電纜設計用于電纜長度從51米(167英尺)到90米(294英尺)的應用，可提供1.0米(3.3英尺)的增量。對于需要1.0米(3.3英尺)…50米(164英尺)電纜長度的Kinetix 5700驅動系統，2090-CSBM1DE (A系列)電纜仍然可用。

Catalog numbers consist of various characters, each of which identifies a specific option for that component. Use the catalog numbering charts below to understａnd the configuration of your component. For questions regarding product availability, contact your Allen-Bradley distributor.

Remove all packing material from within and around the item. After unpacking, verify the catalog number against the purchase order and visually inspect the cable and each connector for damage. If necessary, notify the carrier of any shipping damage immediately.
Cables are stored and shipped in a coil. Cables retain this shape until you straighten the cable. To straighten a cable, hang a short cable from its midpoint or lay a long cable on the floor in a straight line. Any coiling that remains in the cable is straightened out within the next 24 hours. This practice makes the cable easier to install.

The cable technology used in single cables is the same regardless of the catalog number. What is different about each cable is the lead preparation and feedback conductor terminations.
? 2090-CSxM1DF cable conductors have flying-leads and lead preparation that is designed specifically for Kinetix 5500 servo drives. No onsite lead preparation is required.
? 2090-CSxM1DE cables include the 2198-KITCON-DSL connector kit. The kit is pre-assembled with the feedback conductors and lead preparation for the flying-lead power conductors is designed specifically for Kinetix 5700 servo drives. No on-site lead preparation is required.
? 2090-CSxM1DG cable conductors have flying-leads and lead preparation that is designed for either Kinetix 5500 or Kinetix 5700 servo drives. No on-site lead preparation is required, however, 2090-CSxM1DG cable leads are longer than 2090-CSxM1DF cable leads to accommodate either drive family.

These figures illustrate how to measure the bend radius and where cable bends can be made on single motor cables. Use these figures with the cable pinout and specification tables that follow when routing cables during system installation.

To meet the current requirements of motor brake circuits on Kinetix 5700 servo drive systems with cable lengths that exceed 50 m (164 ft), the 2090-CSBM1DE (series B) cables are available with 18 AWG brake conductors. Series B cables are designed for applications with cable lengths from 51 m (167 ft)…90 m (294 ft) and are available in 1.0 m (3.3 ft) increments. For Kinetix 5700 drive systems requiring cable lengths from 1.0 m (3.3 ft)…50 m (164 ft), the 2090-CSBM1DE (series A) cables are still available.